Instructions

Display Case Assembly Instructions

To assemble the display case, first remove all the protective film from both sides of the pieces. Then lay out the pieces on a clean and smooth surface, acrylic is easily scratched so take care. The base piece is the short piece with 4 holes and two slots, the sides are the two long thin pieces with 4 holes and 2 slots, and the top is the short piece with one hole and two slots. The front and back pieces have different notches to match the holes in the sides, top and base. These need to be aligned correctly. Take the base piece and slot the two side pieces in, then slot the front and back panels in place. Place the console inside, and then slot the top piece into place, it should align with the notch in the panel.

Watch Assembly Video Here Shop Display Cases

Controller Holder Assembly Instructions

The two sides and the brace piece will have the protective film on both sides. The film may be blue, white or clear. Remove all of the film before continuing. Once all of the components are pealed, hold one of the sides and slot the brace piece into the slot and push it down. Do exactly the same with the second side so that you end up with the brace piece locked in between the two sides. Align the feet of the sides up with the holes on the base, starting by slotting the back of the side pieces in, and working your way forward in a rolling motion, until the sides are fully located in the base. Once you have located the sides in the slots of the base, your controller holder should be complete.

Watch Assembly Video Here Shop Controller Holders

Controller + Case Assembly Instructions

To assemble the display case, first remove all the protective film from both sides of the pieces. Then lay out the pieces on a clean and smooth surface, acrylic is easily scratched so take care. The base piece is the short piece with 4 holes and two slots, the sides are the two long thin pieces with 4 holes and 2 slots, and the top is the short piece with one hole and two slots. The front and back pieces have different notches to match the holes in the sides, top and base. These need to be aligned correctly. Take the base piece and slot the two side pieces in, then slot the front and back panels in place. Place the controller inside, and then slot the top piece into place, it should align with the notch in the panel.

Watch Assembly Video Here Shop Dual Cases

Controller + Headset Holder Assembly Instructions

First peel all the protective film off all the pieces. Then take one of the headset sides and slot the 4 support braces into the holes. Then take the other headset side and line the holes up with the other end of the braces. Slot the side onto the 4 braces so you have all the clear pieces assembled. Then slot the clear pieces into the base, back notches first and roll down into the front notches. The headset stand is ready for use. If you have a dual headset and controller stand repeat the same actions with the controller pieces. Remove all the protective film. Slot the brace piece into one of the sides, then slot the other side onto the brace. Slot the whole clear piece into the base, back notches first then rolling down into the front notches. The stand is now ready to use.

Watch Assembly Video Here Shop Controller & Headset Stands

Light Switch Surround Fitting Instructions

Designed to be fitted without having to disconnect sockets or switches by trapping the surround between the fascia plate and the wall there is no need for adhesive backing or tapes. Meaning they can be easily removed when decorating or changed to match new colour schemes. First peel the protective film off the surround, taking care not to scratch the acrylic. Then unscrew the fascia plate of the switch/socket, slide the surround diagonally over the plate and then screw the plate back into place. This then ensures the surround is held in place between the plate and the wall. Longer screws may be needed in some instances. Take care not to touch the wiring and ensure the switch/socket is turned off during fitting. If you are unsure, please consult a qualified electrician.

Watch Assembly Video Here Shop Light Switch Surrounds

Tiered Display Stand Assembly Instructions

All parts will have protective film on both sides, except a Mirror Header. The film may be blue, white or clear. Remove all the film before continuing. Then, lay down one of the side pieces and place all the brace pieces into the slots. The number of these will depend on the number of tiers that your stand has. Once all the brace pieces are in the slots, place the other side piece over the brace pieces, carefully placing the brace pieces into the slots one at a time until all the brace pieces are slotted in. Carefully pick up the stand and slowly rotate it so that the back corner is angled upwards. Now you can place the rear support into the slots on the back of the stand. Finally, carefully pick up the stand again and rotate it back around forward, slotting your coloured stands into the remaining slots. If you have a stand with a header slot this into the two remaining slots on the top of the stand.

Watch Assembly Video Here Shop Tiered Stands

Card Holder Assembly Instructions

The two sides and the brace piece will have the protective film on both sides. The film may be blue, white or clear. Remove all of the film before continuing. Once all of the components are pealed, hold one of the sides and slot the brace piece into the slot and push it down. Do exactly the same with the second side so that you end up with the brace piece locked in between the two sides. Align the feet of the sides up with the holes on the base, starting by slotting the back of the side pieces in, and working your way forward in a rolling motion, until the sides are fully located in the base. Once you have located the sides in the slots of the base, your card holder should be complete.

Watch Assembly Video Here Shop Card Holders

Wired Controller Holder Assembly Instructions

The two sides and the brace piece will have the protective film on both sides. The film may be blue, white or clear. Remove all of the film before continuing. Once all of the components are pealed, hold one of the sides and slot the brace piece into the slot and push it down. Do exactly the same with the second side so that you end up with the brace piece locked in between the two sides. Align the feet of the sides up with the holes on the base, starting by slotting the back of the side pieces in, and working your way forward in a rolling motion, until the sides are fully located in the base. Once you have located the sides in the slots of the base, place the controller on the stand, slot the controller plug in one of the sides  and wrap the excess wire around the back of the stand.

Watch Assembly Video Here Shop Controller Holders